The new 228 Series Optical Wavelength Meter from Bristol Instruments combines high accuracy and exceptional repeatability to achieve the most meaningful results for DWDM test applications.

The model 228 is the ideal instrument for precise wavelength characterization of tunable DWDM lasers, DFB lasers, and VCSELs. It can also be used to calibrate passive DWDM component test equipment such as optical spectrum analyzers.

Features:

• Spectral Range: 1250 - 1650 nm (240 - 182 THz)
• Sensitivity: -30 dBm (1 W)
• Absolute optical wavelength measured to the highest accuracy of ± 0.3 pm
• Continuous calibration with a built-in wavelength standard
• Optical wavelength measured to a confidence level of 3σ (≥ 99.6%) Simultaneous measurement of total optical power
• Measurement time as short as 0.1 s

Bristol Instruments

228 Series DWDM Single Wavelength Meter

The new 328 Series Wavelength Meters are designed for single wavelength measurement and utilize FFT processing, similar to the 428 Series Multi-Wavelength Meters.

This allows the 328 Series to measure CW or modulated tunable DWDM lasers, DFB lasers, and VCSELs. The 328 Series is designed for the telecom market. It can also be used to calibrate passive DWDM component test equipment such as optical spectrum analyzers.

Features:

• Spectral Range: 1270 - 1650 nm (236 - 182 THz)
• Sensitivity: -40 dBm (1270 - 1600 nm), -30 dBm (1600 - 1650 nm)
• Absolute optical wavelength measured to an accuracy as high as ± 0.3 pm
• Continuous calibration with a built-in wavelength standard
• Measurement confidence level of 3σ Simultaneous measurement of total optical power
• Operation with CW and modulated signals

Bristol Instruments

328 Series DWDM Single Wavelength Meter

The 428 Series Multi-Wavelength Meter simultaneously measures wavelength, power, and optical signal-to-noise ratio (OSNR) to greater than 40 dB in order to fully characterize DWDM components and DWDM transmission systems.

• Measures wavelength and power of up to 250 optical signals
• Spectral Range: 1270 - 1650 nm (182 - 236 THz)
• Optical wavelength measured to an accuracy as high as ± 0.3 pm
• Continuous calibration with a built-in wavelength standard
• Wavelength accuracy guaranteed to a confidence level of 3δ (≥ 99.6%)
• Automatic calculation of OSNR and channel spacing

Bristol Instruments

428 Series -DWDM Multi-Wavelength Meter

Fabry-Perot Interferometer Mirrors-
Compatible with Burleigh RC series Fabry-Perot interferometers - including models RC-110, RC-140, and RC-150.

• 50.8 mm mirror diameters
• Mirror flatness as high as λ/200
• Standard reflectivity of 99.3%, 97.5%, or 93.0%
• Wavelength coverage from 450nm to 12μm

Bristol Instruments

Fabry Perot Interferometer Mirrors

An OEM solution is needed to monitor laser performance in the system, and possibly to provide fast feedback for system control.Depending on your application various configuration can be used:

• Just a sensor with raw analog output
• Sensor with electronic providing an amplified or digital output
• Complet instrument including numeric display and/or PC interface

Ophir manufactures three main types of pyroelectric OEM sensors:
1. Low profile pyro sensors with no electronics with a BNC output to connect to the host electronics.
2. Low profile smart sensors to be used with Ophir smart display.
3. Compact pyroelectric sensors with built-in amplifiers and signal conditioners which put out a voltage proportional to energy

Main Features:
• Energy Ranges: 2μJ to 20mJ/0.1mJ to 10J
• Spectral Range: 190nm -20µm
• With built-in electronics, for complete self-contained
• OEM solution with calibrated square pulse output

Ophir

OEM Energy Sensors - Standard & Custom